Fire classification to EN 13501-1 class A1
2400 x 1200mm (6mm, 9mm, 12mm and 15mm) Other board sizes are available
RCM Y-wall can be cut, drilled and nailed using conventional hand tools; offering many of the properties of timber.
For cutting the product in any volume, we recommend the use of an RCM polycrystalline diamond Dart Blade to avoid excessive wear on other blades. Alternatively, RCM offer a complete fabrication service, find out more.
For Technical Service or Product Support please file a technical request using our support form or contact your local representative.
Technical Request FormCan’t find the solution you’re looking for? We can help. Our team of experts are on hand to answer your questions.
Contact Us
1200 kg/m3
9-12 MPa
4000 N/mm2
≤0.23 W/mk
≤9%
BS EN 13501-1 Class A1 Non-Combustible
Highly Resistant
Front Face - Smooth
Back Face - Textured
30 years
2400 x 1200mm
6, 9, 12, 15
7.2, 10.8, 14.4, 18
±3mm
±3mm
±0.5mm
BS EN 13501-1:2018 Class A1
BS EN ISO 1716:2018
BS EN ISO 1182:2020
BS EN 1363-1
BS EN 1364-1
BS EN 1365-1
BS 476 Part 4
BS 476 part 22 fire rated through wall solutions
BS EN ISO 12467
BS EN 594 Category 1
BS EN 594:2011
FIX006 - 4.8mm x 38mm Wing tip self drilling fixing
FIX005 - 4.2mm x 42mm Climaseal self drilling fixing
RCM Y-wall can be used as an external sheathing board on structures including where a fire rating is required including those greater than 18m in height, where a structure is over 18m in height RCM Y-wall should be used from ground level all the way up the structure.
RCM Y-wall is classified as A1 non-combustible.
No, RCM Y-wall cannot be left permanently exposed.
RCM Y-wall has one smooth face and one textured face, the smooth face should be fixed outermost.
RCM Dafa tape should be applied to all board to board joints as soon as possible after fixing the boards, unless an airtight seal is required to the external face of the sheathing board, for an airtight seal then the RCM Joint Seal system should be used.
If the joints are taped as soon as the boards are fitted they can be left exposed during the construction phase for up to 3 months, for up to 12 months temporary exposure we highly recommend using the RCM Joint Seal Kit.
RCM Y-wall edge distance is 12-15mm except at the board corners where fixings should be moved up or down to achieve 50mm. Fixings should be fixed using a maximum 600mm x 300mm grid pattern.
We have done our own in-house testing for 12mm RCM Y-Wall. The results suggest a radius of 7.5m or greater, however a structural engineer should ratify this for your project. RCM Y-Wall should not be fixed to a radius but should be cut into vertical strips and fixed to form the curve from a series of flat panels.
RCM can supply Poly Crystalline Diamond (PCD) blades suitable for cutting RCM Y-Wall in a range of diameter and bore sizes, please contact RCM Technical department for further information.
During the early 19th Century, a large section of the South Bank of the River Thames, London, comprised small wharves, docks and other industrial uses. In more recent years, the site has been used as a...
Challenge: The Aurora Apartments were one of several ‘high priority buildings in Scotland to be included...
Collaborative Success in Achieving Enhanced Fire Performance with Y-Wall and Timber Innovations’...
Kent Street is a new development of 504 new homes for Lupa Land in the heart of Birmingham. The site...
Located on the former Anglia Ruskin University site, in the heart of Chelmsford, City Park West is a...
Find out about Y-wall, a high-quality flexible calcium silicate based fibre cement building board, perfect for use as an A1 fire rated sheathing board.
